Plumbing 101: A Necessity for Bathtub Installation
Plumbing 101: A Necessity for Bathtub Installation
Blog Article
What are your beliefs about How to Install a Bathtub?
Setting up a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably difficult project. If the old tub is conveniently available, the job can relocate rapidly; if you have to open a wall surface to eliminate the old tub and place the brand-new bathtub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will certainly require a helper to leave the old tub as well as embeded in the brand-new one. Ensure you have actually qualified yourself for the work and also fit trying it. Instead of employing a service provider to take control of a halfway-completed job, it is much better to think about employing one prior to you start. Possibilities are you may require an expert plumber to make tube connections.
This write-up will help you mount a new bath tub in your shower room if you have currently purchased a brand-new tub and also don't require to change the setup of your previous supply of water pipelines.
Your tools and also material checklist need to comprise the following:
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is detach the water supply. After doing so, activate the faucets to drain pipes any water remaining in the system. The process of removing the existing taps can be quite problematic due to the restricted access that is frequently the case.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth all set for the staying water that will originate from the pipelines. Once the supply pipelines have actually been eliminated, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Prior to moving on to fit the new faucets, contrast the pipe links on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Suitable New Taps
If the tails of the new taps are plastic, then you will require a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a link to the existing supply pipelines.
If you require to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in area between the tap and also the sink. Protect the tap in position with the maker supplied backnut. As soon as the faucet is safely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with regular tap adapters. The former kind should be attached to the tap ends initially, tightening only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been connected.
Setting up the Bath tub
Using the two wooden boards under its feet, put the tub in the required position. The wood boards are helpful in uniformly spreading out the weight of the tub over the location of the boards instead of concentrating all the weight onto four small points.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and adjusting the feet on the bathtub until the level reviews degree.
To set up taps, fit all-time low of the outermost versatile tap adapter to the ideal supply pipeline by making a compression join; after that do the exact same for the other faucet.
Turn on the supply of water and examine all joints as well as new pipework for leaks and also tighten them if needed. Fill the tub and likewise check the overflow electrical outlet and the typical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the producer's user's manual. Tiling and sealing around the tub should wait until the tub has actually been made use of at least once as this will settle it into its final setting.
Planning for the Installment
First of all, the sustaining frame supplied with the bath ought to be fitted (if called for) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is essential to ensure that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps unit to avoid strain on the bathtub.
Fit the adaptable faucet connectors to the bottom of both faucets making use of 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bathroom must now be ready to be suited its last setting.
Tiling Around the Bath tub
In the location where the bathroom meets the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to break an inflexible seal, causing the water to penetrate the wall between the bath as well as the tiling, causing issues with wetness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your components as well as installations. They are offered in tubes and also cartridges, and can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Remember to always fill up the bath tub with water prior to sealing, to enable the activity experienced when the bathtub remains in use. The sealant can split rather very early if you do not consider this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the market. It is recommended to fit the tiles using water-resistant or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a reader on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I think sharing that piece of content was worthwhile. Those who appreciated our blog post please be sure to share it. We value reading our article about How to Install a Bathtub Yourself.
Order Repair Report this page